Rear Mech hanger

Greg · Joined: 25 Jan 2008 Posts: 503 Location: Billingham

Help needed please, snapped my hanger today Embarassed

Were can I get a replacment, It was to late to phone bike scene, so I thought I would get a ahead of the game and try crc but could not find one fit my bike?

I need to get one sharpish to get back on the trails.

Ohh is't for a spec stumpy fsr 120, 05 i think

cheers

Greg

Denny69 · Joined: 11 Sep 2007 Posts: 720 Location: Stockton on Tees

Try Wiggle Greg. I would hedge my bets on Bikescene as they're a "Spesh" dealer.

Greg · Joined: 25 Jan 2008 Posts: 503 Location: Billingham

yeh, tried there too, no luck. may have wait till bikescene open.

cheers

Greg

Greg · Joined: 25 Jan 2008 Posts: 503 Location: Billingham

Found one on edinburgh bicycles, also has a list of what fits what model,

worth a look if you ever need to replace one

Gunner · Posted: Sun Apr 27, 2008 12:11 pm Post subject: Re: Rear Mech hanger

Greg · Joined: 25 Jan 2008 Posts: 503 Location: Billingham

Hi Gunner,

I was on a down hill with lots of loose branches and a big one got stuck in my back wheel and must have ripped my mech/ hanger off, glad that the xtr mech still looks ok.

Tried to do a temp fix taking off the mech and convert to single speed but the chain was to long, should have took a chain tool....

Gunner · Posted: Sun Apr 27, 2008 4:38 pm Post subject:

Sounds about right, same thing happened to me on Eston Hills many years ago, and again in Battersby Plantation.

Nothing for it but a long jog home pushing the bike Rolling Eyes

Greg · Joined: 25 Jan 2008 Posts: 503 Location: Billingham

I was lucky as it was at the back-end of the ride and it was mostly down hill!

Are these hangers easy to set up, looks like its only 2 bolts

cheers

Greg

Gunner · Posted: Mon Apr 28, 2008 7:27 pm Post subject:

The hanger should be easy enough to fit, but if I remember correctly a special tool is used to check its alignment once fitted, as poor alignment can have a big impact on smooth shifting.

Wink

Greg · Joined: 25 Jan 2008 Posts: 503 Location: Billingham

cheers Gunner, may get the shop to fine tune!

matt.will · Joined: 13 Jan 2008 Posts: 224

Dunno about spesh's but on my GT the frame and hanger were shaped to fit one onother so you couldn't go wrong fitting it - I think others are usually the same. They're an expensive way of buying a small piece of metal, but they've got you by the short and curlys pretty much!

Greg · Joined: 25 Jan 2008 Posts: 503 Location: Billingham

cheers matt,

got hanger fitted but now I carnt get all the gears Confused

.

Dunna why as hanger only fits one way on frame, the only other fitting is the mech to hanger guess this is the problem.

Any one got any ideas?

Gunner · Posted: Wed Apr 30, 2008 7:38 am Post subject:

You are not missing any spacers, or washers are you from the hanger to the mech. Sorry, but that's the best I can think of, apart from maybe you needing to tackle the problem using the "HIGH-LOW" screws on the mech itself to correct this, or maybe a cable adjustment.........

Try Googling for the tool I mentioned, if you can find out what it does and how, you may be able to bodge around without it, i.e. it must make suggestions as to what to do if the tool shows your hanger is not aligned, if you see what I mean Confused

Greg · Joined: 25 Jan 2008 Posts: 503 Location: Billingham

cheers Gunner

Denny69 · Joined: 11 Sep 2007 Posts: 720 Location: Stockton on Tees

If you can't find the tool you can use a couple of adjustable spanners....hard to describe but it's all in THE BIKE BOOK 4th edition....if you wanna borrow it let me know.

	MTBE Forum Index -> The Workshop	All times are GMT Goto page 1, 2 Next
Page 1 of 2